Bathroom Faucet: Single Handle Bathroom Faucet with Pop Up Drain and Deck Plate, Bathroom Faucet 1 or 3 Hole, Vanity Faucet Sink Drain, Grifo para Lavamanos Baño, Brushed Nickel

This is a great faucet and a nice drain popup, and for the price it is fantastic!A few installation tips:If your old drain is corroded and will not unscrew easily, don't fight it trying to take it apart. Get an angle grinder and a cut off disk. It took me about a minute to cut off the end of the tailpiece that had the sidearm where the operating lever for the pop up drain stopper goes into the tailpiece as well as cutting the retaining nut into two halves.Tip 1:Hand tighten the supply line hoses that go into the bottom of the faucet. The seal is an o-ring between the sides of the hose and the inside of the fitting. One of the faucets I got leaked like crazy from the cold water hose as it entered the faucet at the bottom. Hand tightening the hose fixed that. The hot water hose was also very loose.Tip 2:There is a large diameter slotted nut that secures the faucet to the sink. It has two large Phillips screws on it to lock down that nut. Back those two screws out until the are flush with the face of the nut. That way when you tighten the screws down to lock the faucet in place, they won't bend outwards and walk off the big flat metal washer they should be pressing against.Tip 3: There is a large caliber threaded extension at the base of the faucet that the slotted nut in Tip 2 screws on to. This was not tightened down on either of the faucets I installed. Just hand tighten themTip 4: When attaching the water supply lines to the shut off valves, keep the hoses from twisting as you tighten the compression nut on to the shut off valve. I used a pair of pliers on the metal part of the hose just above the compression nut, gripping firmly but making sure not to crush the fitting. If the hose unscrews too far it will back the supply hose out of the faucet (see Tip 1).Tip 5: The drain assembly _will_ leak without teflon tape. The problem is the large tapered silicone washer that goes between the bottom of the sink and the washer/threaded sleeve. It is not soft enough to press into the threads around the tailpiece, allowing water to flow past the washer. By putting a lot of teflon tape in the area where the threaded sleeve and tailpiece screw together (the lower parts of the thread on our sinks), any water that gets by the tapered silicone washer will get trapped by the teflon in the threads and the base of the washer. Also use a slip joint (water pump) plier or plumbers wrench to tighten the threaded sleeve on to the tailpiece. That improves the chance of forcing the silicone of the tapered washer into the threads to make a seal higher up.These are great to look at an a pleasure to use, replacing 30 year old faucets and drains. Hard to say how long they will hold up, but for now they look and feel great!

The AMAZING FORCE single handle bathroom faucet exudes contemporary elegance in my newly remodeled master bath. With crisp lines and a beautiful brushed nickel finish, it elevates the style of my vanity and complements my contemporary decor perfectly.Beyond its sleek, sophisticated styling, this faucet delivers outstanding performance. Installation took less than 20 minutes - the included instructions and mounting hardware made the process very straightforward. The solid brass construction feels substantial and I can tell it is made to last.I absolutely love the smooth, drip-free handle operation. With just a delicate turn, I can adjust from a gentle trickle to full pressure. And the aerator creates a gentle yet powerful enough stream to clean my hands and toothbrush with little effort.After using it, a simple wipe down keeps the brushed nickel finish looking as flawless as the day I installed it. I don't have to worry about spots, stains or scratches marring its smooth surface over time.On top of bringing modern elegance to my bathroom, the AMAZING FORCE faucet provides flawless performance day after day. I highly recommend it as beautiful, reliable upgrade!

I bought five of these and the install went smoothly except I struggled with achieving a watertight seal at the drain. Long story short, this was solved by wrapping teflon tape on the threads before adding the rubber washer (see pictures). The push-button drain closed/open system works great! Recommended, especially for the price.

The media could not be loaded.  Totally purchased 4 faucets to replace all my old ones. Already replaced 2 of them. BTW removing old Moen took 2-3 times more time than installing this new one. Old mounting hardware was so rusty and stubborn to remove. Amazing Force is all stainless steel so there will be no problem in the future.Installation is easy and you don't need any teflon tape or plumbers putty to get watertight connections. Just properly tight drain by hand. Rubber gloves will help you to get better grip. Drain come with thick soft rubber gasket which will properly seal everything. See my under sink picture. Just above stainless flange is white rubberlike really thick gasket. Manufacturer apparently changed design (based on reviews / feedback ?) There is no logo on the top (see my picture). Only H and C letters obviously. Also faucet diameter is 1 1/4 inch so will easily fit three hole sinks. Not 1 3/8 as some people claims. Checked with calipers. My sinks are 23 years old and accepted this faucet without any problems. No need to enlarge hole.Water supply lines are color coded for cold / hot water and a good quality braided stainless steel.I and my wife really like this design, it is very nice, has great water flow. Note: It is good after installing water lines remove (unscrew) aerator and then run water for a few seconds. First water will go really dirty and can clog aerator. After flushing lines install it back and you are done.The only thing I will improve is central mounting plate needed for three hole install. It's little too small to cover stains left by the previous faucet. Will prefer more square. But this is not an issue with a new install.UPDATE: Installed two more. One of those had reversed water supply lines. Red marked line need to be connected to cold water for proper work. Not a big issue but surprise after installation - cold water instead of hot. Go under cabinet and reverse lines. This is obvious that nobody is testing those faucets in the factory.I also remembered to record removing aerator and running first water after install. So you can clearly see not so clear water.

We have not had any paint/metal chipping or leaking since install at the end of December. Install did not take my husband very long. The handle is loose enough for my kids to use but not to loose.

i m sure price is double at lowes and home depot. great value.

Muy bonita, tuve que conseguir adaptadores especiales porque en cdmx tenía otra medida de las llaves de agua, pero en general buen!

This is a great buy yo change my bathrooms for the guests and looks great.

The faucet is well made, and I am satisfied with the purchase.

Looks ok but will review again in a few months. One issue is the spout is off center by a few mm. Didn't notice it until it install. Not terrible and doesn't affect use but it speaks to quality standards.

The title did not lie ! The force on this thing is incredible LOL. Nice finish, looks like the photos. The design was perfect for my needs.